Replies: 11 comments 27 replies
-
|
I have been tinkering with this board as well. |
Beta Was this translation helpful? Give feedback.
-
|
Here is a demo configuration of LovyanGFX for this board. Without the actual hardware, there is not much I can do to assist at this point. Maybe other users can help? First try to compile the demo projects from the vendor and/or the example above and see if that works. |
Beta Was this translation helpful? Give feedback.
-
|
Update: This board is now added to the automated nightly builds. Feel free to test it and provide feedback here. |
Beta Was this translation helpful? Give feedback.
-
|
@jesse-schein has been working on a config for this board. Maybe he can share his experience here? |
Beta Was this translation helpful? Give feedback.
-
|
Yea I got it working just fine. Ran into issues with the different spi bus. Will require device specific code for this board to make it work which made me question the code quality. This branch will work on the board, not quite the latest from master. |
Beta Was this translation helpful? Give feedback.
-
|
Thank you all for your replies. I tried with the branch of @jesse-schein and built the setup with environment esp32-2432S028R_4MB . |
Beta Was this translation helpful? Give feedback.
-
|
Same issue here. |
Beta Was this translation helpful? Give feedback.
-
|
Hacked in a backlight directly into the code to test, and then it works. |
Beta Was this translation helpful? Give feedback.
-
|
Hi @PhantomSage , Where exactly have you placed this code to try it also on my side ? |
Beta Was this translation helpful? Give feedback.
-
|
"Uggly", but "works for me(TM)". ==== hasp_gui.cpp ==== ++ pinMode(21,OUTPUT); #if HASP_USE_MQTT > 0 #if HASP_USE_GPIO > 0 ++ pinMode(21,OUTPUT); #if HASP_USE_MDNS > 0 |
Beta Was this translation helpful? Give feedback.
-
|
Hi @PhantomSage , |
Beta Was this translation helpful? Give feedback.
-
|
@jesse-schein or @xliner78 or @PhantomSage |
Beta Was this translation helpful? Give feedback.
-
|
I want to say I will, but the code to make the SPI touch and screen work needs rework in my branch. I'm about to leave for my honeymoon for a long time so I simply dont have the time. Maybe when I get back if no one else can, at least I made it work sorta..... I got the backlight to work by making these backlight changes inside of the website for hasp management of configs, thats probably why its omitted in my code. I still havent looked at my other computer if I missed checking anything in..... been slammed. |
Beta Was this translation helpful? Give feedback.
-
|
Have a nice honemoon! |
Beta Was this translation helpful? Give feedback.
-
|
I have been able to correct the entry and made it a bit more elegant, wrapping the additional lines in a flag, that is being passed from screen definition file, so it is applied only to this lcd type. If only it would be merged with the main repo... |
Beta Was this translation helpful? Give feedback.
-
|
I have received my order. This board is now added to the automated nightly builds. Feel free to test it and provide feedback here. Thanks to @jesse-schein and macsbug for sharing their config. I also added resistive touch calibration, so no need to hardcode the calibration values anymore. |
Beta Was this translation helpful? Give feedback.
-
|
Works like a charm, once a calibration has been performed :) |
Beta Was this translation helpful? Give feedback.
-
|
Hi, Regards |
Beta Was this translation helpful? Give feedback.
-
|
I wanted to post here what i did (with @fvanroie help) to get the new version of this board (With USB-C) to work well. I originally had several issues including 25% of the screen being garbled pixels, inverted colors, and touch not working. The steps below got me to a seemingly fully functional setup. I have not tried the GPIOs but i cant imagine they will be a problem.
These are the only changes i made to an otherwise virgin git clone. |
Beta Was this translation helpful? Give feedback.
-
|
I had to change
into
to have my touch working right. (Don't forget to calibrate touch.) |
Beta Was this translation helpful? Give feedback.
-
|
@fvanroie I managed to flash the 2432S028R version to the device and the result is similar to what @bort900 described.
|
Beta Was this translation helpful? Give feedback.
-
|
Use |
Beta Was this translation helpful? Give feedback.
-
|
@fvanroie Thanks a lot for the ultra-quick reply. I managed to flash it to the device using Espressif flasher. I expect that this particular hardware version with USB-C is the new standard i.e. from Aliexpress. |
Beta Was this translation helpful? Give feedback.
-
How to download it - I have the same problem. it seems the configuration is for 320x240 display |
Beta Was this translation helpful? Give feedback.
-
|
Just for those reading along : if after initial setup your touch does not work:
It is documented, but hey... |
Beta Was this translation helpful? Give feedback.
-
|
I've been using openHASP on my CYD and I've been been pretty impressed with it, I've managed to get the moodlight working with HA but I can't really work out how to get the LDR working. Is it supported? |
Beta Was this translation helpful? Give feedback.
-
|
I recently upgraded my ESP32-2432S028 from 0.7.0-rc4 to 0.7.0-rc6 and its really hurt my wifi stability. http to the plate doesn't work at all. When I connect via serial I see the wifi connection go up and down. I would like to temporarily move back to rc4 but the nightly build dropdown doesn't show it. How can I get the rc4 version? While I'm at it I have another issue. I tried to get a few more plates working in Home Assistant but none of my new plates show up in HA or any debug logs (they are all running 0.7.0-rc6). I can see that they are emitting mqtt requests but Home Assistant has not set up any entities for the new plates. |
Beta Was this translation helpful? Give feedback.
-
|
What pins are used for uart on the P1 bus for RX and TX? And how to set in yaml for Home Assistant Audio - speaker on GPIO 26. Thanks |
Beta Was this translation helpful? Give feedback.
-
Hi,
I just bought this board from Aliexpress https://www.aliexpress.com/item/1005004502250619.html but I cannot work with openHasp. Here are the schematics of the board but I don't have any idea how to make it working with this board
Kind regards
Dimos
Beta Was this translation helpful? Give feedback.
All reactions