diff --git a/libraries/BLE/aci_setup.cpp b/libraries/BLE/aci_setup.cpp
index ab014ee..beff032 100644
--- a/libraries/BLE/aci_setup.cpp
+++ b/libraries/BLE/aci_setup.cpp
@@ -63,6 +63,9 @@ static bool aci_setup_fill(aci_state_t *aci_stat, uint8_t *num_cmd_offset)
 		//Add 2 bytes to the length byte for status byte, length for the total number of bytes
 		memcpy(&msg_to_send, &(aci_stat->aci_setup_info.setup_msgs[*num_cmd_offset]), 
 				  (aci_stat->aci_setup_info.setup_msgs[*num_cmd_offset].buffer[0]+2)); 
+	#elif defined(__SAM3X8E__)
+		memcpy(&msg_to_send, &(aci_stat->aci_setup_info.setup_msgs[*num_cmd_offset]), 
+				  (aci_stat->aci_setup_info.setup_msgs[*num_cmd_offset].buffer[0]+2));
 	#endif
 
     //Put the Setup ACI message in the command queue
diff --git a/libraries/BLE/boards.h b/libraries/BLE/boards.h
index e1ea98d..4cf5f2b 100644
--- a/libraries/BLE/boards.h
+++ b/libraries/BLE/boards.h
@@ -28,7 +28,9 @@
 
 #define BOARD_DEFAULT               0 //Use this if you do not know the board you are using or you are creating a new one
 #define REDBEARLAB_SHIELD_V1_1      1 //Redbearlab Bluetooth low energy shield v1.1
-#define REDBEARLAB_SHIELD_V2012_07  1 //Identical to Redbearlab v1.1 shield
+#define REDBEARLAB_SHIELD_V2012_07  1 //Redbearlab Bluetooth low energy shield v2012.07
 #define REDBEARLAB_SHIELD_V2        0 //Redbearlab Bluetooth low energy shield v2.x - No special handling required for pin reset same as default
+#define REDBEARLAB_BLEND						0 //Redbearlab Bluetooth low energy Blend - No special handling required for pin reset same as default
+#define REDBEARLAB_BLEND_MICRO			0 //Redbearlab Bluetooth low energy Blend Micro - No special handling required for pin reset same as default
 
 #endif
\ No newline at end of file
diff --git a/libraries/BLE/hal_aci_tl.cpp b/libraries/BLE/hal_aci_tl.cpp
index f1b1214..1f7d417 100644
--- a/libraries/BLE/hal_aci_tl.cpp
+++ b/libraries/BLE/hal_aci_tl.cpp
@@ -27,9 +27,11 @@
 #include "hal_platform.h"
 #include "hal_aci_tl.h"
 #include "aci_queue.h"
+
 #if ( !defined(__SAM3X8E__) && !defined(__PIC32MX__) )
 #include <avr/sleep.h>
 #endif
+
 /*
 PIC32 supports only MSbit transfer on SPI and the nRF8001 uses LSBit
 Use the REVERSE_BITS macro to convert from MSBit to LSBit
@@ -80,7 +82,7 @@ void m_aci_data_print(hal_aci_data_t *p_data)
   Interrupt service routine called when the RDYN line goes low. Runs the SPI transfer.
 */
 static void m_aci_isr(void)
-{
+{	
   hal_aci_data_t data_to_send;
   hal_aci_data_t received_data;
 
@@ -346,6 +348,12 @@ void hal_aci_tl_init(aci_pins_t *a_pins, bool debug)
 
   The SPI library assumes that the hardware pins are used
   */
+#if defined(__SAM3X8E__)
+	SPI.begin          (DUE_SPI_CSN);
+  SPI.setBitOrder    (DUE_SPI_CSN, LSBFIRST);
+  SPI.setClockDivider(DUE_SPI_CSN, a_pins->spi_clock_divider); /* This will run the SPI at 3MHz assuming a 84MHz clock to the mcu*/
+  SPI.setDataMode    (DUE_SPI_CSN, SPI_MODE0);
+#else
   SPI.begin();
   //Board dependent defines
   #if defined (__AVR__)
@@ -357,6 +365,7 @@ void hal_aci_tl_init(aci_pins_t *a_pins, bool debug)
   #endif
   SPI.setClockDivider(a_pins->spi_clock_divider);
   SPI.setDataMode(SPI_MODE0);
+#endif
 
   /* Initialize the ACI Command queue. This must be called after the delay above. */
   aci_queue_init(&aci_tx_q);
@@ -429,6 +438,8 @@ static uint8_t spi_readwrite(const uint8_t aci_byte)
     uint8_t tmp_bits;
     tmp_bits = SPI.transfer(REVERSE_BITS(aci_byte));
 	return REVERSE_BITS(tmp_bits);
+#elif defined(__SAM3X8E__)
+	return SPI.transfer(DUE_SPI_CSN, aci_byte, SPI_CONTINUE);
 #endif
 }
 
diff --git a/libraries/BLE/hal_platform.h b/libraries/BLE/hal_platform.h
index ebe05c3..165bd2b 100644
--- a/libraries/BLE/hal_platform.h
+++ b/libraries/BLE/hal_platform.h
@@ -68,6 +68,19 @@
 	
 	//Redefine the function for reading from flash in ChipKit
 	#define memcpy_P        memcpy
+#elif defined(__SAM3X8E__)
+		/* definition for DUE */
+		#include "Arduino.h"
+
+		#define F(X) (X)
+		#undef PSTR
+		#define PSTR(x) (x)
+		#define PROGMEM
+		
+		#define pgm_read_byte_near(x) (x)
+		#define memcpy_P memcpy
+		
+		#define DUE_SPI_CSN            52
 #endif
 
 #endif /* PLATFORM_H__ */
diff --git a/libraries/BLE/lib_aci.cpp b/libraries/BLE/lib_aci.cpp
index 8332e48..f4b7e71 100644
--- a/libraries/BLE/lib_aci.cpp
+++ b/libraries/BLE/lib_aci.cpp
@@ -103,7 +103,11 @@ void lib_aci_board_init(aci_state_t *aci_stat)
 	hal_aci_evt_t *aci_data = NULL;
 	aci_data = (hal_aci_evt_t *)&msg_to_send;
 					
-	if (REDBEARLAB_SHIELD_V1_1 == aci_stat->aci_pins.board_name)
+	if (REDBEARLAB_SHIELD_V1_1 == aci_stat->aci_pins.board_name
+		|| REDBEARLAB_SHIELD_V2012_07 == aci_stat->aci_pins.board_name
+		|| REDBEARLAB_SHIELD_V2 == aci_stat->aci_pins.board_name
+		|| REDBEARLAB_BLEND == aci_stat->aci_pins.board_name
+		|| REDBEARLAB_BLEND_MICRO == aci_stat->aci_pins.board_name)
 	{
 	  /*
 	  The Bluetooth low energy Arduino shield v1.1 requires about 100ms to reset.