I cannot start the BBBW

[SayethRd]

Hi, I tried to follow the quick start guide, but shortly after I turn on the Beaglebone, the user LEDs turn off and I can no longer access to the "kind of storage Beaglebone". I don't know if it is user error or my Beaglebone is broken. Please help me.

[d-c-d]

I've had good luck with both BBB and BBBW - were you able to verify that your micro SD card is inserted properly and is programmed correctly?

Do you have an HDMI monitor connected?
What about a serial monitor?

[SayethRd]

System boots from eMMC memory, I verified that the user LEDs shows the 'boot up', then the usr0 LED blink in a heartbeat pattern, but shortly after all LEDs turned off :/

[nvskraju]

@SayethRd
Hi SayethRd,

Did you find the root cause for this issue? I am also seeing the same problem on my board first the board gets recognized after 1-2 minutes i am getting usb was not recognized and boards get disconnected (then the usr0 LED blink in a heartbeat pattern, but shortly after all LEDs turned off )

[SayethRd]

I don't know exactly what is the root cause, but it fixed when I put the antennas (of Wi-Fi and Bluetooth) out of the board. Tell me if it works on your Beagle too.

[nvskraju]

Thank you SayethRd for immediate response, Today morning i have connected my BBB to my computer again with out any changes but it started working.

…

On Fri, May 15, 2020 at 10:10 AM SayethRd ***@***.***> wrote: I don't know exactly what is the root cause, but it fixed when I put the antennas (of Wi-Fi and Bluetooth) out of the board. Tell me if it works on your Beagle too. — You are receiving this because you commented. Reply to this email directly, view it on GitHub <#13 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AEYSHNUSRJJ6LUVKRRRZHMTRRVEN3ANCNFSM4F7N7QOA> .

[SayethRd]

It happened to my BBB to, but eventually it stopped working untill I put the antennas out of the board (like the box image). I hope it not happen to your BBB.

[nvskraju]

Hi SayethRd, 1. i thought you told me to remove the antenna connectors before 2.My board also worked after i placed the antennas pointing outside the board (just as you said like box image). Thank You

…

On Sat, May 16, 2020 at 2:03 AM SayethRd ***@***.***> wrote: It happened to my BBB to, but eventually it stopped working untill I put the antennas out of the board (like the box image). I hope it not happen to your BBB. — You are receiving this because you commented. Reply to this email directly, view it on GitHub <#13 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AEYSHNQHYXESG2TISOBYHSTRRYUC7ANCNFSM4F7N7QOA> .

[SayethRd]

Good. Sorry if I wasn't clear before 😅.

[nvskraju]

Thank you very much for your help. I am a beginner, could you please Suggest some specific websites particularly for beagle bone black wireless for a beginner.

…

On Thu, May 21, 2020 at 11:12 AM SayethRd ***@***.***> wrote: Good. Sorry if I wasn't clear before 😅. — You are receiving this because you commented. Reply to this email directly, view it on GitHub <#13 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AEYSHNQGVNGVVVMZ7BI7XZ3RSVAG5ANCNFSM4F7N7QOA> .

[SayethRd]

Humm sorry, I just read the Exploring Beaglebone book 😅, but I think the Beaglebone Cookbook is useful for beringers.

[nvskraju]

Thank you for the information 🙏

…

On Thu, May 21, 2020 at 3:39 PM SayethRd ***@***.***> wrote: Humm sorry, I just read the Exploring Beaglebone book 😅, but I think the Beaglebone Cookbook is useful for beringers. — You are receiving this because you commented. Reply to this email directly, view it on GitHub <#13 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/AEYSHNXEZP2NXXDTI7WM33LRSV7QPANCNFSM4F7N7QOA> .