| Test Board | SDIO Module HW |
|---|---|
 |
 |
6.1.111-rt42
DISTRIB_ID=Ubuntu
DISTRIB_RELEASE=20.04
DISTRIB_CODENAME=focal
DISTRIB_DESCRIPTION="Ubuntu 20.04.2 LTS"
Architecture: aarch64
CPU op-mode(s): 32-bit, 64-bit
Byte Order: Little Endian
CPU(s): 2
On-line CPU(s) list: 0,1
Thread(s) per core: 1
Core(s) per socket: 2
Socket(s): 1
Vendor ID: ARM
Model: 0
Model name: Cortex-A35
Stepping: r1p0
BogoMIPS: 66.66
Vulnerability Gather data sampling: Not affected
Vulnerability Itlb multihit: Not affected
Vulnerability L1tf: Not affected
Vulnerability Mds: Not affected
Vulnerability Meltdown: Not affected
Vulnerability Mmio stale data: Not affected
Vulnerability Reg file data sampling: Not affected
Vulnerability Retbleed: Not affected
Vulnerability Spec rstack overflow: Not affected
Vulnerability Spec store bypass: Not affected
Vulnerability Spectre v1: Mitigation; __user pointer sanitization
Vulnerability Spectre v2: Not affected
Vulnerability Srbds: Not affected
Vulnerability Tsx async abort: Not affected
Flags: fp asimd evtstrm aes pmull sha1 sha2 crc32 cpuid
MMC_TYPE=SDIO
SDIO_ID=024C:D723
SDIO_REVISION=0.0
clock: 50000000 Hz
actual clock: 50000000 Hz
vdd: 21 (3.3 ~ 3.4 V)
bus mode: 2 (push-pull)
chip select: 0 (don't care)
power mode: 2 (on)
bus width: 2 (4 bits)
timing spec: 2 (sd high-speed)
signal voltage: 0 (3.30 V)
driver type: 0 (driver type B)
The driver is loaded via "insmod"
Module Size Used by
rtw_8723ds 16384 0
rtw_8723d 45056 1 rtw_8723ds
rtw_8723x 20480 1 rtw_8723d
rtw_sdio 20480 1 rtw_8723ds
rtw_core 217088 3 rtw_8723d,rtw_sdio,rtw_8723x
iw list
Wiphy phy0
max # scan SSIDs: 4
max scan IEs length: 2257 bytes
max # sched scan SSIDs: 0
max # match sets: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports T-DLS.
Supported Ciphers:
* WEP40 (00-0f-ac:1)
* WEP104 (00-0f-ac:5)
* TKIP (00-0f-ac:2)
* CCMP-128 (00-0f-ac:4)
* CCMP-256 (00-0f-ac:10)
* GCMP-128 (00-0f-ac:8)
* GCMP-256 (00-0f-ac:9)
* CMAC (00-0f-ac:6)
* CMAC-256 (00-0f-ac:13)
* GMAC-128 (00-0f-ac:11)
* GMAC-256 (00-0f-ac:12)
Available Antennas: TX 0x1 RX 0x1
Configured Antennas: TX 0x1 RX 0x1
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* monitor
* P2P-client
* P2P-GO
Band 1:
Capabilities: 0x196e
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
RX STBC 1-stream
Max AMSDU length: 7935 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 16 usec (0x07)
HT Max RX data rate: 150 Mbps
HT TX/RX MCS rate indexes supported: 0-7, 32
Bitrates (non-HT):
* 1.0 Mbps
* 2.0 Mbps
* 5.5 Mbps
* 11.0 Mbps
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Frequencies:
* 2412 MHz [1] (20.0 dBm)
* 2417 MHz [2] (20.0 dBm)
* 2422 MHz [3] (20.0 dBm)
* 2427 MHz [4] (20.0 dBm)
* 2432 MHz [5] (20.0 dBm)
* 2437 MHz [6] (20.0 dBm)
* 2442 MHz [7] (20.0 dBm)
* 2447 MHz [8] (20.0 dBm)
* 2452 MHz [9] (20.0 dBm)
* 2457 MHz [10] (20.0 dBm)
* 2462 MHz [11] (20.0 dBm)
* 2467 MHz [12] (20.0 dBm)
* 2472 MHz [13] (20.0 dBm)
* 2484 MHz [14] (disabled)
Supported commands:
* new_interface
* set_interface
* new_key
* start_ap
* new_station
* set_bss
* authenticate
* associate
* deauthenticate
* disassociate
* join_ibss
* remain_on_channel
* set_tx_bitrate_mask
* frame
* frame_wait_cancel
* set_wiphy_netns
* set_channel
* tdls_mgmt
* tdls_oper
* probe_client
* set_noack_map
* register_beacons
* start_p2p_device
* set_mcast_rate
* connect
* disconnect
* set_qos_map
* set_multicast_to_unicast
* Unknown command (140)
software interface modes (can always be added):
* AP/VLAN
* monitor
valid interface combinations:
* #{ managed } <= 1, #{ AP, P2P-client, P2P-GO } <= 1,
total <= 2, #channels <= 1
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
Device supports TX status socket option.
Device supports HT-IBSS.
Device supports SAE with AUTHENTICATE command
Device supports scan flush.
Device supports per-vif TX power setting
Driver supports full state transitions for AP/GO clients
Driver supports a userspace MPM
Device supports configuring vdev MAC-addr on create.
Device supports randomizing MAC-addr in scans.
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Supported TX frame types:
* IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
* P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
Supported RX frame types:
* IBSS: 0x40 0xb0 0xc0 0xd0
* managed: 0x40 0xb0 0xd0
* AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* mesh point: 0xb0 0xc0 0xd0
* P2P-client: 0x40 0xd0
* P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
* P2P-device: 0x40 0xd0
Supported extended features:
* [ RRM ]: RRM
* [ SET_SCAN_DWELL ]: scan dwell setting
* [ FILS_STA ]: STA FILS (Fast Initial Link Setup)
* [ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
* [ TXQS ]: FQ-CoDel-enabled intermediate TXQs
wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 192.168.1.17 netmask 255.255.252.0 broadcast 192.168.3.255
RX packets 15 bytes 2643 (2.6 KB)
RX errors 0 dropped 1 overruns 0 frame 0
TX packets 27 bytes 4849 (4.8 KB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
wlan0 IEEE 802.11 ESSID:""
Mode:Managed Frequency:2.412 GHz Access Point:
Bit Rate=6 Mb/s Tx-Power=20 dBm
Retry short limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:on
Link Quality=36/70 Signal level=-74 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
Retrieving speedtest.net configuration...
Retrieving speedtest.net server list...
Selecting best server based on ping...
Testing download speed................................................................................
Download: 16.42 Mbit/s
Testing upload speed......................................................................................................
Upload: 2.43 Mbit/s
PING 8.8.8.8 (8.8.8.8) 56(84) bytes of data.
64 bytes from 8.8.8.8: icmp_seq=1 ttl=118 time=9.76 ms
64 bytes from 8.8.8.8: icmp_seq=2 ttl=118 time=5.70 ms
64 bytes from 8.8.8.8: icmp_seq=3 ttl=118 time=11.9 ms
64 bytes from 8.8.8.8: icmp_seq=4 ttl=118 time=6.92 ms
64 bytes from 8.8.8.8: icmp_seq=5 ttl=118 time=11.0 ms
64 bytes from 8.8.8.8: icmp_seq=6 ttl=118 time=6.69 ms
64 bytes from 8.8.8.8: icmp_seq=7 ttl=118 time=9.93 ms
64 bytes from 8.8.8.8: icmp_seq=8 ttl=118 time=5.76 ms
64 bytes from 8.8.8.8: icmp_seq=9 ttl=118 time=10.6 ms
64 bytes from 8.8.8.8: icmp_seq=10 ttl=118 time=5.10 ms
64 bytes from 8.8.8.8: icmp_seq=11 ttl=118 time=19.6 ms
64 bytes from 8.8.8.8: icmp_seq=12 ttl=118 time=12.6 ms
64 bytes from 8.8.8.8: icmp_seq=13 ttl=118 time=7.97 ms
64 bytes from 8.8.8.8: icmp_seq=14 ttl=118 time=4.61 ms
64 bytes from 8.8.8.8: icmp_seq=15 ttl=118 time=5.80 ms
64 bytes from 8.8.8.8: icmp_seq=16 ttl=118 time=6.27 ms
64 bytes from 8.8.8.8: icmp_seq=17 ttl=118 time=10.3 ms
64 bytes from 8.8.8.8: icmp_seq=18 ttl=118 time=4.20 ms
64 bytes from 8.8.8.8: icmp_seq=19 ttl=118 time=4.41 ms
64 bytes from 8.8.8.8: icmp_seq=20 ttl=118 time=8.42 ms
--- 8.8.8.8 ping statistics ---
20 packets transmitted, 20 received, 0% packet loss, time 19029ms
rtt min/avg/max/mdev = 4.204/8.381/19.626/3.642 ms
PING 192.168.1.17 (192.168.1.17) 10000(10028) bytes of data.
10008 bytes from 192.168.1.17: icmp_seq=1 ttl=64 time=0.128 ms
10008 bytes from 192.168.1.17: icmp_seq=2 ttl=64 time=0.148 ms
10008 bytes from 192.168.1.17: icmp_seq=3 ttl=64 time=0.093 ms
10008 bytes from 192.168.1.17: icmp_seq=4 ttl=64 time=0.098 ms
10008 bytes from 192.168.1.17: icmp_seq=5 ttl=64 time=0.152 ms
10008 bytes from 192.168.1.17: icmp_seq=6 ttl=64 time=0.144 ms
10008 bytes from 192.168.1.17: icmp_seq=7 ttl=64 time=0.117 ms
10008 bytes from 192.168.1.17: icmp_seq=8 ttl=64 time=0.138 ms
10008 bytes from 192.168.1.17: icmp_seq=9 ttl=64 time=0.109 ms
10008 bytes from 192.168.1.17: icmp_seq=10 ttl=64 time=0.104 ms
10008 bytes from 192.168.1.17: icmp_seq=11 ttl=64 time=0.125 ms
10008 bytes from 192.168.1.17: icmp_seq=12 ttl=64 time=0.151 ms
10008 bytes from 192.168.1.17: icmp_seq=13 ttl=64 time=0.146 ms
10008 bytes from 192.168.1.17: icmp_seq=14 ttl=64 time=0.143 ms
10008 bytes from 192.168.1.17: icmp_seq=15 ttl=64 time=0.099 ms
10008 bytes from 192.168.1.17: icmp_seq=16 ttl=64 time=0.098 ms
10008 bytes from 192.168.1.17: icmp_seq=17 ttl=64 time=0.113 ms
10008 bytes from 192.168.1.17: icmp_seq=18 ttl=64 time=0.154 ms
10008 bytes from 192.168.1.17: icmp_seq=19 ttl=64 time=0.170 ms
10008 bytes from 192.168.1.17: icmp_seq=20 ttl=64 time=0.142 ms
--- 192.168.1.17 ping statistics ---
20 packets transmitted, 20 received, 0% packet loss, time 19464ms
rtt min/avg/max/mdev = 0.093/0.128/0.170/0.022 ms
iperf3
-----------------------------------------------------------
Server listening on 5201
-----------------------------------------------------------
Accepted connection from 192.168.1.3, port 61045
[ 5] local 192.168.1.17 port 5201 connected to 192.168.1.3 port 61046
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 704 KBytes 5.77 Mbits/sec 0 69.9 KBytes
[ 5] 1.00-2.00 sec 157 KBytes 1.28 Mbits/sec 0 69.9 KBytes
[ 5] 2.00-3.00 sec 314 KBytes 2.57 Mbits/sec 1 69.9 KBytes
[ 5] 3.00-4.00 sec 157 KBytes 1.28 Mbits/sec 0 69.9 KBytes
[ 5] 4.00-5.00 sec 157 KBytes 1.28 Mbits/sec 1 69.9 KBytes
[ 5] 5.00-6.00 sec 157 KBytes 1.29 Mbits/sec 1 69.9 KBytes
[ 5] 6.00-7.00 sec 0.00 Bytes 0.00 bits/sec 0 1.43 KBytes
[ 5] 7.00-8.00 sec 0.00 Bytes 0.00 bits/sec 0 1.43 KBytes
[ 5] 8.00-9.00 sec 0.00 Bytes 0.00 bits/sec 0 1.43 KBytes
[ 5] 9.00-10.00 sec 0.00 Bytes 0.00 bits/sec 0 1.43 KBytes
[ 5] 10.00-11.00 sec 0.00 Bytes 0.00 bits/sec 0 1.43 KBytes
[ 5] 11.00-12.00 sec 0.00 Bytes 0.00 bits/sec 0 1.43 KBytes
[ 5] 12.00-13.00 sec 0.00 Bytes 0.00 bits/sec 0 1.43 KBytes
[ 5] 13.00-14.00 sec 0.00 Bytes 0.00 bits/sec 0 1.43 KBytes
[ 5] 14.00-15.00 sec 0.00 Bytes 0.00 bits/sec 0 1.43 KBytes
[ 5] 15.00-16.00 sec 0.00 Bytes 0.00 bits/sec 0 1.43 KBytes
[ 5] 16.00-17.00 sec 0.00 Bytes 0.00 bits/sec 0 1.43 KBytes
[ 5] 17.00-18.00 sec 0.00 Bytes 0.00 bits/sec 0 1.43 KBytes
[ 5] 18.00-19.00 sec 0.00 Bytes 0.00 bits/sec 0 1.43 KBytes
[ 5] 19.00-20.00 sec 0.00 Bytes 0.00 bits/sec 0 1.43 KBytes
[ 5] 20.00-21.00 sec 0.00 Bytes 0.00 bits/sec 1 69.9 KBytes
[ 5] 21.00-22.00 sec 0.00 Bytes 0.00 bits/sec 0 69.9 KBytes
[ 5] 22.00-23.00 sec 157 KBytes 1.29 Mbits/sec 0 69.9 KBytes
[ 5] 23.00-24.00 sec 157 KBytes 1.28 Mbits/sec 0 69.9 KBytes
[ 5] 24.00-25.00 sec 345 KBytes 2.83 Mbits/sec 0 69.9 KBytes
[ 5] 25.00-26.00 sec 0.00 Bytes 0.00 bits/sec 1 69.9 KBytes
[ 5] 26.00-27.00 sec 314 KBytes 2.57 Mbits/sec 0 69.9 KBytes
[ 5] 27.00-28.00 sec 188 KBytes 1.54 Mbits/sec 0 69.9 KBytes
[ 5] 28.00-29.00 sec 314 KBytes 2.57 Mbits/sec 0 69.9 KBytes
[ 5] 29.00-30.00 sec 314 KBytes 2.57 Mbits/sec 0 69.9 KBytes
[ 5] 30.00-30.16 sec 0.00 Bytes 0.00 bits/sec 0 69.9 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-30.16 sec 3.35 MBytes 933 Kbits/sec 5 sender
-----------------------------------------------------------
Server listening on 5201
-----------------------------------------------------------
[ 261.999351] rtw_core: loading out-of-tree module taints kernel.
[ 262.714269] rtw_8723ds mmc1:0001:1: Firmware version 48.0.0, H2C version 0
[ 370.665267] rtw_8723ds mmc1:0001:1: failed to get tx report from firmware
Setup the configuration at /etc/hostapd/hostapd.conf
interface=wlan0
driver=nl80211
ieee80211n=1
hw_mode=g
channel=6
ssid=AP-TEST
wpa=2
wpa_passphrase=12345678
wpa_key_mgmt=WPA-PSK
rsn_pairwise=CCMP TKIP
wpa_pairwise=TKIP CCMP
start 192.168.175.2
end 192.168.175.254
interface wlan0
max_leases 234
opt router 192.168.175.1
sudo hostapd /etc/hostapd/hostapd.conf -B
Using interface wlan0 with hwaddr and ssid "AP-NAME"
wlan0: interface state UNINITIALIZED->ENABLED
wlan0: AP-ENABLED
Host unable to connect!
iperf3
Wlan0 Not Ready.
Start AP @ WLAN0
Configuration file: /etc/hostapd/hostapd.conf
Using interface wlan0 with hwaddr 34:75:63:28:4b:e4 and ssid "AP-TEST"
wlan0: interface state UNINITIALIZED->ENABLED
wlan0: AP-ENABLED
-----------------------------------------------------------
Server listening on 5201
-----------------------------------------------------------
[ 261.999351] rtw_core: loading out-of-tree module taints kernel.
[ 262.714269] rtw_8723ds mmc1:0001:1: Firmware version 48.0.0, H2C version 0
[ 370.665267] rtw_8723ds mmc1:0001:1: failed to get tx report from firmware