v10.0.0

[dalathegreat]

What's Changed 📦

This release focuses on longterm stability, by improving the ESP32 library base, partitioning schemes, flash frequencies and flash size. It turbocharges the Stark CMR hardware, unlocking the full potential of the board as a large 8MB memory device.

Taking this release into use ⚙️

Caution

USB reflash required to take v10 into use!

Note that v10 is a major new release of the Battery-Emulator software. The first time when taking a v10 version into use, you are required to perform an initial one time USB setup via this webpage! This is because we are changing the flash frequencies, partitioning layouts and other under the hood changes to ensure longterm system stability. After any v10 has been installed via USB, following 10.X.X releases can be updated over the air. Sorry for any inconvenience!

Quickstart video: https://youtu.be/sR3t7j0R9Z0

Setting up a board for the first time? Use this webpage to flash the board!

What's Changed

Batteries 🔋

• New battery: Added support for 2012-2020 Tesla S/X batteries, Legacy Tesla integration , by @dalathegreat in New battery: Support for older 2012-2020 Tesla S/X batteries #1946
• New battery, Added "Growatt HV Ark" support, by @ErikssonPer in New Battery, Growatt HV ARK #2018
• New battery: Added "Emus G1 BMS" support via the PylonHV integration by @ErikssonPer in New battery Emus G1 BMS supported by Pylon_HV integration #1998
• Think City: Several startup reliabaility improvements by @dalathegreat in Bugfix: Think City CAN values #2004
• Stellantis ECMP: Tighten low-voltage chargestop limits to avoid undercharged batteries by @dalathegreat in Bugfix: ECMP; Tighten low-voltage chargestop limits  #2007
• BMW iX: Added additional DTC descriptions by @lenvm in BMW iX: add additional DTC descriptions #2009
• Bugfix: Pylon Battery, make double-battery support work by @dalathegreat in Bugfix: Pylon, make double-battery support work #2000

Inverters ⚡

• Pylon LV: Prevent voltage bouncing due to repeatedly charge/discharge by @M4GNV5 in Prevent voltage bouncing due to repeadetly charge/discharge with Pylon LV #1988
• Fronius: Changed how voltages/capacity is written towards inverter, to avoid false positive warnings when using BYD Atto3 batteries or simialar ones, by @pmajor021 in Testing the maximum capacity and voltage readings with the Fronius Primo and BYD Atto3 #1966

Connectivity 🛜

• MQTT: Replace watchdog timer with 60s check to reduce chances of getting watchdog resets @jonny5532 in MQTT: Replace watchdog timer with 60s check from connectivity loop #1893
• MQTT: Improved cell voltage discovery by @No-Signal in Fixing MQTT cell voltage discovery #2020

Hardware 🤖

• Stark CMR: Turbocharge the Stark CMR to become a large flash (8MB) device by @dalathegreat in Feature: Update Stark to 8MB + Update ESP32 to 3.3.6 #1986

Housekeeping 🧹

• Feature: Update ESP32 to v3.3.5 by @dalathegreat in Feature: Update Stark to 8MB + Update ESP32 to 3.3.6 #1986
• Improvement: Inform user of low memory situation by @dalathegreat in Improvement: Inform user of low memory situation + ESP downgrade #1997
• Housekeeping: Bring back -Werror compile flag by @dalathegreat in Housekeeping: Bring back -Werror compile flag #2028
• Improvement: Reduce flash usage further by @dalathegreat in Improvement: Reduce flash usage further #1979

Full Changelog: v9.3.5...v10.0.0

---

This discussion was created from the release v10.0.0.

[Lyzwa01]

Hello, I have a question. In the project it says there is 8 MB of memory, but in the T-CAN485 there is physically only 4 MB. Will this not cause a conflict?