Nethsm v2 updates (#375)

* Rename NetHSM v1 images to include version

* Add front and back side images for NetHSM v2

* Add note about redundant power supplies

* Remove redundant power supplies from planned features

* Add note about to network configuration for NetHSM v1

* Add NetHSM v2 system recovery descriptions

source/components/nethsm/administration.rst

@@ -366,7 +366,7 @@ Network
 The network configuration defines the settings used for the *Network Port*.
 
 .. note::
-   This settings do not configure the *BMC Network Port*.
+   This settings do not configure the *BMC Network Port* on the NetHSM 1.
 
 
 The network configuration can be retrieved as follows.

source/components/nethsm/faq.rst

@@ -32,5 +32,3 @@ Frequently Asked Questions (FAQ)
    * More user rights management (e.g. additional roles, groups)
    * Further separations and hardenings
    * FIPS and/or Common Criteria certifications
-   * Redundant power supplies
-

source/components/nethsm/getting-started.rst

@@ -64,15 +64,15 @@ Please follow the three step process closely to verify that it has arrived safel
 3. After verifying that the sealing of the wrapping paper is not broken, remove the wrapping paper.
    Finally, check the four seals on the side of the NetHSM hardware.
 
-   .. figure:: ./images/server-top-with-seal-positions.jpg
+   .. figure:: ./images/nethsm1-top-with-seal-positions.jpg
       :scale: 100
       :alt: Positions of the four seals
 
       Positions of the four seals
 
       |
 
-   .. figure:: ./images/server-side-with-seal.jpg
+   .. figure:: ./images/nethsm1-side-with-seal.jpg
       :scale: 100
       :alt: Seal on the side of the chassis
 
@@ -89,11 +89,27 @@ Please follow the two step process closely to install the NetHSM hardware.
 1. Connect the power cable with the *Power Port*, and the network cable with the *Network Port*.
    Further, press the *Power Switch* to turn on power.
 
-   .. figure:: ./images/server-back-with-labels.png
-      :scale: 100
-      :alt: Back side of the server
+   .. tabs::
+      .. tab:: NetHSM 2
+
+         .. figure:: ./images/nethsm2-back-with-labels.png
+            :scale: 100
+            :alt: Back side of the server
+
+         Back side of the server
+
+         .. important::
+
+            The NetHSM 2 has redundant power supplies, which both need to be supplied with power.
+            Undersupply causes the power supply to emit a beep sound.
+
+      .. tab:: NetHSM 1
 
-      Back side of the server
+         .. figure:: ./images/nethsm1-back-with-labels.png
+            :scale: 100
+            :alt: Back side of the server
+
+         Back side of the server
 
 2. Press the *Power Button* to turn on the NetHSM hardware.
    The *Reset Button* is only for a forced reboot of the NetHSM hardware.
@@ -103,11 +119,22 @@ Please follow the two step process closely to install the NetHSM hardware.
 
       Do not use the *BMC Network Port* because it allows wider system access.
 
-   .. figure:: ./images/server-front-with-labels.png
-      :scale: 100
-      :alt: Front side of the server
+   .. tabs::
+      .. tab:: NetHSM 2
+
+         .. figure:: ./images/nethsm2-front-with-labels.png
+            :scale: 100
+            :alt: Front side of the server
+
+            Front side of the server
+
+      .. tab:: NetHSM 1
+
+         .. figure:: ./images/nethsm1-front-with-labels.png
+            :scale: 100
+            :alt: Front side of the server
 
-      Front side of the server
+            Front side of the server
 
 In an unprovisioned state the NetHSM hardware factory default IP address is ``192.168.1.1``.